DigiTrak F5® Transmitters

DCI's F5 single-frequency transmitters have light green tubes and share the same dimensions as other DigiTrak transmitters. They come in two frequency designations: 18.5kHz and 8.4 kHz. These transmitters are only for use with the F5 locating system.

DCI's F5 single-frequency transmitters have light green tubes and share the same dimensions as other DigiTrak transmitters. They come in two frequency designations: 18.5kHz and 8.4 kHz. These transmitters are only for use with the F5 locating system.

The F5 dual-frequency transmitters (Model HDT) come in two configurations:  19.2 kHz/12 kHz and 12 kHz/1.3 kHz.  These transmitters have light-green tubes and incorporate the new mechanical design like that used for the fluid pressure transmitters.  The new design has a knurled battery cap that is not flush with the battery compartment, as the older version was.  With the cap installed, the overall length is still 15 in. (38.1 cm), but without the cap the length is 14.6 in. (37.08 cm).  Thus, the HDT transmitters are compatible with existing drill housings that accommodate 15 in. (38.1 cm) DigiTrak transmitters. If using a tooling adapter, however, the new design will require a different adapter. 

The F5 dual-frequency transmitters (Model HDT) come in two configurations:  19.2 kHz/12 kHz and 12 kHz/1.3 kHz.  These transmitters have light-green tubes and incorporate the new mechanical design like that used for the fluid pressure transmitters.  The new design has a knurled battery cap that is not flush with the battery compartment, as the older version was.  With the cap installed, the overall length is still 15 in. (38.1 cm), but without the cap the length is 14.6 in. (37.08 cm).  Thus, the HDT transmitters are compatible with existing drill housings that accommodate 15 in. (38.1 cm) DigiTrak transmitters. If using a tooling adapter, however, the new design will require a different adapter. 

The long-range DigiTrak F5 Fluid Pressure Transmitter (Model FPT) provides downhole fluid pressure monitoring up to 250 psi (1725 kPa). The drilling fluid pressure is measured through sensor ports located on the front end cap on either side of the index slot. The FPT is available in two dual-frequency configurations:  19.2 kHz/12 kHz and 12 kHz/1.3 kHz.  These transmitters have light-green tubes and incorporate a new mechanical design, in addition to the fluid pressure sensors.  The new design has a knurled battery cap that is not flush with the battery compartment, as the older version was.  With the cap installed, the overall length is still 15 in. (38.1 cm), but without the cap the length is 14.6 in. (37.08 cm).  Thus, the FPT transmitters are compatible with existing drill housings that accommodate 15 in. (38.1 cm) DigiTrak transmitters.  If using a tooling adapter, however, the new design will require a different adapter.  Also, the housings must allow fluid to flow to the sensor ports for measurement of the drilling fluid pressure.

The long-range DigiTrak F5 Fluid Pressure Transmitter (Model FPT) provides downhole fluid pressure monitoring up to 250 psi (1725 kPa). The drilling fluid pressure is measured through sensor ports located on the front end cap on either side of the index slot. The FPT is available in two dual-frequency configurations:  19.2 kHz/12 kHz and 12 kHz/1.3 kHz.  These transmitters have light-green tubes and incorporate a new mechanical design, in addition to the fluid pressure sensors.  The new design has a knurled battery cap that is not flush with the battery compartment, as the older version was.  With the cap installed, the overall length is still 15 in. (38.1 cm), but without the cap the length is 14.6 in. (37.08 cm).  Thus, the FPT transmitters are compatible with existing drill housings that accommodate 15 in. (38.1 cm) DigiTrak transmitters.  If using a tooling adapter, however, the new design will require a different adapter.  Also, the housings must allow fluid to flow to the sensor ports for measurement of the drilling fluid pressure.

DCI's F5 single-frequency transmitters have light green tubes and share the same dimensions as other DigiTrak transmitters. They come in two frequency designations: 18.5kHz and 8.4 kHz. These transmitters are only for use with the F5 locating system.

DCI's F5 single-frequency transmitters have light green tubes and share the same dimensions as other DigiTrak transmitters. They come in two frequency designations: 18.5kHz and 8.4 kHz. These transmitters are only for use with the F5 locating system.

The F5 dual-frequency transmitters (Model HDT) come in two configurations:  19.2 kHz/12 kHz and 12 kHz/1.3 kHz.  These transmitters have light-green tubes and incorporate the new mechanical design like that used for the fluid pressure transmitters.  The new design has a knurled battery cap that is not flush with the battery compartment, as the older version was.  With the cap installed, the overall length is still 15 in. (38.1 cm), but without the cap the length is 14.6 in. (37.08 cm).  Thus, the HDT transmitters are compatible with existing drill housings that accommodate 15 in. (38.1 cm) DigiTrak transmitters. If using a tooling adapter, however, the new design will require a different adapter. 

The F5 dual-frequency transmitters (Model HDT) come in two configurations:  19.2 kHz/12 kHz and 12 kHz/1.3 kHz.  These transmitters have light-green tubes and incorporate the new mechanical design like that used for the fluid pressure transmitters.  The new design has a knurled battery cap that is not flush with the battery compartment, as the older version was.  With the cap installed, the overall length is still 15 in. (38.1 cm), but without the cap the length is 14.6 in. (37.08 cm).  Thus, the HDT transmitters are compatible with existing drill housings that accommodate 15 in. (38.1 cm) DigiTrak transmitters. If using a tooling adapter, however, the new design will require a different adapter. 

The long-range DigiTrak F5 Fluid Pressure Transmitter (Model FPT) provides downhole fluid pressure monitoring up to 250 psi (1725 kPa). The drilling fluid pressure is measured through sensor ports located on the front end cap on either side of the index slot. The FPT is available in two dual-frequency configurations:  19.2 kHz/12 kHz and 12 kHz/1.3 kHz.  These transmitters have light-green tubes and incorporate a new mechanical design, in addition to the fluid pressure sensors.  The new design has a knurled battery cap that is not flush with the battery compartment, as the older version was.  With the cap installed, the overall length is still 15 in. (38.1 cm), but without the cap the length is 14.6 in. (37.08 cm).  Thus, the FPT transmitters are compatible with existing drill housings that accommodate 15 in. (38.1 cm) DigiTrak transmitters.  If using a tooling adapter, however, the new design will require a different adapter.  Also, the housings must allow fluid to flow to the sensor ports for measurement of the drilling fluid pressure.

The long-range DigiTrak F5 Fluid Pressure Transmitter (Model FPT) provides downhole fluid pressure monitoring up to 250 psi (1725 kPa). The drilling fluid pressure is measured through sensor ports located on the front end cap on either side of the index slot. The FPT is available in two dual-frequency configurations:  19.2 kHz/12 kHz and 12 kHz/1.3 kHz.  These transmitters have light-green tubes and incorporate a new mechanical design, in addition to the fluid pressure sensors.  The new design has a knurled battery cap that is not flush with the battery compartment, as the older version was.  With the cap installed, the overall length is still 15 in. (38.1 cm), but without the cap the length is 14.6 in. (37.08 cm).  Thus, the FPT transmitters are compatible with existing drill housings that accommodate 15 in. (38.1 cm) DigiTrak transmitters.  If using a tooling adapter, however, the new design will require a different adapter.  Also, the housings must allow fluid to flow to the sensor ports for measurement of the drilling fluid pressure.